Discussion:
Fixing / patching holes in plasterboard for ceiling lights that are slightly too big
(too old to reply)
c***@gmail.com
2018-03-09 11:04:13 UTC
Permalink
The holes cut for the GU10 ceiling lights are slightly too big and the edges of the plaster board look rough. Is there a reliable way to fix this so the finish appears better?

Thanks,

Clive
GB
2018-03-09 11:17:33 UTC
Permalink
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the edges of the plaster board look rough. Is there a reliable way to fix this so the finish appears better?
Thanks,
Clive
Google downlight hole reducer plate
or downlight hole concealer ring
The Natural Philosopher
2018-03-09 11:20:50 UTC
Permalink
Post by GB
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the
edges of the plaster board look rough. Is there a reliable way to fix
this so the finish appears better?
Thanks,
Clive
Google downlight hole reducer plate
or downlight hole concealer ring
Or buy some paint, some plaster and some sandpaper
--
New Socialism consists essentially in being seen to have your heart in
the right place whilst your head is in the clouds and your hand is in
someone else's pocket.
t***@gmail.com
2018-03-09 11:33:58 UTC
Permalink
Post by The Natural Philosopher
Post by GB
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the
edges of the plaster board look rough. Is there a reliable way to fix
this so the finish appears better?
Thanks,
Clive
Google downlight hole reducer plate
or downlight hole concealer ring
Or buy some paint, some plaster and some sandpaper
and pva, it'll all be weak otherwise


NT
c***@gmail.com
2018-03-09 12:34:22 UTC
Permalink
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the edges of the plaster board look rough. Is there a reliable way to fix this so the finish appears better?
Thanks,
Clive
Hi All,

I was concerned I could spend a lot of effort trying to fill the space between the light fitting and the hole in the plasterboard (it isnt large) then the filler falling out because it has little except the edge of the hole to "cling" to. The downlight hole concealer ring looks a viable option. If the plastic is thin enough I might even be able to recess it in the plasterboard, stick it with contact adhesive liek GripFill, then cover the surface of the ring with filler. Or the concealer ring might be so discrete I wont bother trying to recess and disguise it therby potentially causing more damage to the ceiling.

Thanks for the suggestions,


Clive
Jonathan
2018-03-09 14:27:35 UTC
Permalink
Post by c***@gmail.com
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the edges of the plaster board look rough. Is there a reliable way to fix this so the finish appears better?
Thanks,
Clive
Hi All,
I was concerned I could spend a lot of effort trying to fill the space between the light fitting and the hole in the plasterboard (it isnt large) then the filler falling out because it has little except the edge of the hole to "cling" to. The downlight hole concealer ring looks a viable option. If the plastic is thin enough I might even be able to recess it in the plasterboard, stick it with contact adhesive liek GripFill, then cover the surface of the ring with filler. Or the concealer ring might be so discrete I wont bother trying to recess and disguise it therby potentially causing more damage to the ceiling.
Thanks for the suggestions,
Clive
I glued some cardboard strips with PVA when I changed our kitchen light fittings for some smaller ones. It worked fine as the fittings covered the cardboard.

Jonathan
Andrew
2018-03-09 20:11:02 UTC
Permalink
Post by Jonathan
Post by c***@gmail.com
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the edges of the plaster board look rough. Is there a reliable way to fix this so the finish appears better?
Thanks,
Clive
Hi All,
I was concerned I could spend a lot of effort trying to fill the space between the light fitting and the hole in the plasterboard (it isnt large) then the filler falling out because it has little except the edge of the hole to "cling" to. The downlight hole concealer ring looks a viable option. If the plastic is thin enough I might even be able to recess it in the plasterboard, stick it with contact adhesive liek GripFill, then cover the surface of the ring with filler. Or the concealer ring might be so discrete I wont bother trying to recess and disguise it therby potentially causing more damage to the ceiling.
Thanks for the suggestions,
Clive
I glued some cardboard strips with PVA when I changed our kitchen light fittings for some smaller ones. It worked fine as the fittings covered the cardboard.
Jonathan
Hope you don't have a kitchen fire then !.
ss
2018-03-09 20:48:22 UTC
Permalink
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the
edges of the plaster board look rough. Is there a reliable way to fix
this so the finish appears better?
Another option would be to cut out a square panel from the ceiling, fit
a new panel with correct size hole. New panel fitted with a couple of
battens filled and smoothed at joints.
ARW
2018-03-12 21:28:59 UTC
Permalink
Post by Andrew
Post by Jonathan
Post by c***@gmail.com
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and
the edges of the plaster board look rough. Is there a reliable way
to fix this so the finish appears better?
Thanks,
Clive
Hi All,
I was concerned I could spend a lot of effort trying to fill the
space between the light fitting and the hole in the plasterboard (it
isnt large) then the filler falling out because it has little except
the edge of the hole to "cling" to. The downlight hole concealer ring
looks a viable option. If the plastic is thin enough I might even be
able to recess it in the plasterboard, stick it with contact adhesive
liek GripFill, then cover the surface of the ring with filler. Or the
concealer ring might be so discrete I wont bother trying to recess
and disguise it therby potentially causing more damage to the ceiling.
Thanks for the suggestions,
Clive
I glued some cardboard strips with PVA when I changed our kitchen
light fittings for some smaller ones. It worked fine as the fittings
covered the cardboard.
Jonathan
Hope you don't have a kitchen fire then !.
So do I but unless it is a fire rated ceiling it will not matter.
--
Adam
Rob Morley
2018-03-12 17:36:12 UTC
Permalink
On Fri, 9 Mar 2018 03:04:13 -0800 (PST)
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and
the edges of the plaster board look rough. Is there a reliable way to
fix this so the finish appears better?
Cut a hole the right size in a bit of hardboard, then cut that in half
so you can pass it through the hole in the plasterboard and glue it in
position. Then use filler to build up the the plasterboard to the edge
of the hardboard. You'll probably want to first soak the edge of the
plasterboard with dilute PVA to stop it sucking and/or crumbling.
Scott
2019-11-23 10:02:49 UTC
Permalink
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the edges of the plaster board look rough. Is there a reliable way to fix this so the finish appears better?
Thanks,
What about One Strike?
https://www.everbuild.co.uk/product/one-strike/
Brian Gaff (Sofa 2)
2019-11-23 10:11:32 UTC
Permalink
Only about a year and a half late then.
Brian
--
----- --
This newsgroup posting comes to you directly from...
The Sofa of Brian Gaff...
***@blueyonder.co.uk
Blind user, so no pictures please
Note this Signature is meaningless.!
Post by Scott
Post by c***@gmail.com
The holes cut for the GU10 ceiling lights are slightly too big and the
edges of the plaster board look rough. Is there a reliable way to fix this
so the finish appears better?
Thanks,
What about One Strike?
https://www.everbuild.co.uk/product/one-strike/
Loading...